Philips TAB8505
* The preview only show first 10 pages of manuals. Please download to view the full documents.
Loading preview... Please wait.
Manuals Content
User manual 8000 Series TAB8505
Register your product and get support at www.philips.com/support
Contents 1 Important
3
4 Use your Soundbar
16
Safety
3
Turn ON and OFF
16
Care for your product
4
Auto Standby
16
Care of the environment
4
Select Modes
16
Compliance
4
Adjust the Volume
16
Help and support
4
Dolby sound mode
16
Factory Reset
17
Setup Menu
17
Bluetooth Operation
18
Caution FCC and IC statement for Users (USA and Canada only)
2 Your Soundbar
5 6
What’s in the Box
6
Main unit
6
Connectors
7
Wireless subwoofer
7
Remote control
8
Prepare the Remote Control
8
Placement
9
Wall mount
3 Connect
10 11
Dolby Atmos®
11
Connect to HDMI Socket
11
Connect to Optical Socket
12
Connect to AUX Socket
12
Connect to Power
13
Pair up with the subwoofer
13
Connect to Wi-Fi (Wireless Operation)
2
14
AUX / OPTICAL / HDMI ARC Operation
19
USB Operation
19
Listen to Spotify
19
Upgrade Firmware
20
3URGXFWVSHFLÀFDWLRQV
21
6 Troubleshooting
22
Read and understand all instructions before you use your product. If damage is caused by failure to follow instructions, the warranty does not apply.
Safety 5LVNRIHOHFWULFVKRFNRUÀUH • Before you make or change any connections, make sure that all devices are disconnected from the power outlet. • Never expose the product and accessories to rain or water. Never place liquid containers, such as vases, near the product. If liquids are spilt on or into the product, disconnect it from the power outlet immediately. Contact Consumer Care to have the product checked before use. • Never place the product and accessories QHDUQDNHGÁDPHVRURWKHUKHDWVRXUFHV including direct sunlight. • Never insert objects into the ventilation slots or other openings on the product. • Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. • Battery (battery pack or batteries installed) shall not be exposed to excessive heat VXFKDVVXQVKLQHÀUHRUWKHOLNH • Disconnect the product from the power outlet before lightning storms. • When you disconnect the power cord, always pull the plug, never the cable. • Use the product in tropical and/or moderate climates. 5LVNRIVKRUWFLUFXLWRUÀUH • )RULGHQWLÀFDWLRQDQGVXSSO\UDWLQJVVHH the type plate at the back or bottom of the product. • Before you connect the product to the power outlet, ensure that the power voltage matches the value printed on the back or bottom of the product. Never connect the product to the power outlet if the voltage is different.
5LVNRILQMXU\RUGDPDJHWRWKLVSURGXFW • For wall mounting, this product must be securely attached to the wall in accordance with the installation instructions. Use only the supplied wall mount bracket (if available). Improper wall mounting may result in accident, injury or damage. If you have any query, contact Consumer Care in your country. • Never place the product or any objects on power cords or on other electrical equipment. • If the product is transported in temperatures below 5°C, unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet. • Parts of this product can be made of glass. Handle with care to avoid injury and damage. 5LVNRIRYHUKHDWLQJ • 1HYHULQVWDOOWKLVSURGXFWLQDFRQÀQHG space. Always leave a space of at least four inches around the product for ventilation. Ensure curtains or other objects never cover the ventilation slots on the product. 5LVNRIFRQWDPLQDWLRQ • Do not mix batteries (old and new or carbon and alkaine, etc.). • CAUTION: Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type. • Remove batteries if they are exhausted or if the remote control is not to be used for a long time. • Batteries contain chemical substances, they should be disposed of properly. 5LVNRIVZDOORZLQJEDWWHULHV • The product/remote control may contain a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. Severe internal burns can occur within two hours of ingestion. • If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention. • When you change the batteries, always keep all new and used batteries out of reach of children. Ensure that the battery compartment is completely secure after you replace the battery. 3
English
1 Important
•
If the battery compartment cannot be completely secured, discontinue use of the product. Keep out of reach of children and contact the manufacturer.
This is CLASS II apparatus with double insulation, and no protective earth provided. AC voltage
products and batteries. Follow local rules and never dispose of the product and batteries with normal household waste. Correct disposal of old products and batteries helps prevent negative consequences for the environment and human health. Removing the disposable batteries To remove the disposable batteries, see battery installation section. For 5G WiFi Device
The device for operation in the band 5150–5350 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Use only the power supplies listed in the user manual.
Care for your product 8VHRQO\PLFURÀEHUFORWKWRFOHDQWKHSURGXFW
Care of the environment
Compliance
Disposal of your old product and battery
This product complies with the radio interference requirements of the European Community. Hereby,TP Vision Europe B.V. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
This symbol on a product means that the product is covered by European Directive 2012/19/EU.
This symbol means that the product contains batteries covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. Inform yourself about the local separate collection system for electrical and electronic 4
www.p4c.philips.com.
Help and support For extensive online support, visit www.philips.com/support to: • download the user manual and the quick start guide • watch video tutorials (available only for selected models) • ÀQGDQVZHUVWRIUHTXHQWO\DQVZHUHG questions (FAQs) • email us a question • chat with our support representative.
Caution FCC and IC statement for Users (USA and Canada only) FCC INFORMATION NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio / TV technician for help.
IC-Canada: CAN IECES-3(B)/NMB-3(B) This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
FCC&IC Warning: • •
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. &KDQJHVRUPRGLÀFDWLRQVWRWKLVXQLWQRW expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ”
5
English
Follow the instructions on the website to select your language, and then enter your product model number. Alternatively, you can contact Consumer Care in your country. Before you contact, note down the model number and serial number of your SURGXFW
2 Your Soundbar
Main unit This section includes an overview of the main unit.
Congratulations on your purchase, and ZHOFRPHWR3KLOLSV7RIXOO\EHQHÀWIURP the support that Philips offers, register your Soundbar at www.philips.com/support.
a
b
c
d
e
What’s in the Box Check and identify the items in the package:
00
•
Soundbar
x1
•
Wireless Subwoofer
x1
•
Remote Control
x1
•
Power Cord *
x4
Wall Mount kit
x1
• •
(Wall Brackets x2, Screws x2, Dowels x2)
Quick Start Guide / Warranty Card / Safety Sheet / Wall Mount Template x 1
f
Remote Control
Quick start guide
b + (Volume) button Increase the volume. (Play/Pause) button Start, pause or resume play. • •
(Source)/Bluetooth pairing button Select an input source for the Soundbar. Press and hold to activate the pairing function in Bluetooth mode or disconnect the existing paired Bluetooth device. (Standby-On) button
e
Power Action State On
2X 2X 2X
Power Cord *
Wall Bracket Gum Cover Screws (for wall)
* Power cord quantity and plug type vary by regions.
Warranty Card Safety Sheet Wall Mount Template
*
Power cord quantity and plug type vary by regions.
•
Images, illustrations and drawings shown on this User Manual are for reference only, actual product may vary in appearance.
6
i
a - (Volume) button Decrease the volume.
d
Wireless Subwoofer
g
h
c Soundbar
:0 0
Press the Semi button Standby once
Function
• Follow source state • Wi-Fi is still on. • It still supports Play-Fi and Airplay2.
• Wi-Fi is off. Press and • The product enters the lower hold
Eco Standby button 5 seconds
power consumption mode.
• Restarting the system will take a relatively longer time.
f Display panel g Remote Control Sensor
i Wi-Fi LED indicator (Yellow) LED State
Status
Wi-Fi Access Point (AP) mode Blink Double blink Wi-Fi Protected Setup (WPS) mode Constant on Connected / Pairing successful
English
e HDMI OUT (eARC/ARC) Connect to the HDMI input on the TV.
h Power LED
f HDMI 1/ HDMI 2 Connect to the HDMI input on the TV. g AC~ Socket Connect to the power supply. h Wall bracket slot
Connectors
Wireless subwoofer
This section includes an overview of the connectors available on your Soundbar.
This section includes an overview of the Wireless subwoofer.
h
a abc
a
• •
d
e
f
g
USB Audio input from a USB storage device. Upgrade software of this product.
b AUX Audio input from, for example, an MP3 player (3.5mm jack). c OPTICAL Connect to an optical audio output on the TV or a digital device. d
• • •
bc
a AC~ Socket Connect to the power supply. b Pair button Press and hold to enter the pairing mode for the subwoofer. c Subwoofer indicator Determine the status based on the wireless subwoofer indicator. LED State
Status
Fast blink
Subwoofer in pairing mode
Constant on
Connected / Pairing successful
Slow blink
Connection / Pairing Failed
(Wi-Fi Setup) button Trigger Wi-Fi setup for Play-Fi. Press and hold the button for 3 seconds to active the Wps mode. Press and hold the button for 8 seconds to active the AP mode.
7
Remote control This section includes an overview of the remote control. (Standby-On)
a
Power Action State
Function
• Follow source state Press the • Wi-Fi is still on. Semi button • It still supports Play-Fi and Standby once Airplay2.
On
Press and hold Eco Standby button 5 seconds
b
• Wi-Fi is off. • The product enters the lower •
power consumption mode. Restarting the system will take a relatively longer time.
(Dolby) Turn the Dolby ON/OFF.
d
(Mute) Mute or restore volume.
• , •
/
• • g h
8
/
,
,
(Cursors)
(Previous/Next) Skip to the previous or next track in USB / BT / PLAY-Fi mode. Navigate Left/Right in menu structure. Navigate Down/Up in menu structure.
(MENU) Enter setup menu. • •
c
d f
e g
h
i
j
i
+/- (Soundbar’s Volume) Increase / decrease the soundbar’s volume.
j
+/- (Subwoofer’s Volume) Increase / decrease the subwoofer’s volume.
(Play/Pause) Start, pause or resume play in USB / BT / PLAY-Fi mode. &RQÀUPDVHOHFWLRQ
•
f
b
(Source) Select an input source for the Soundbar. Press and hold to activate the pairing function in Bluetooth mode or disconnect the existing paired Bluetooth device.
• •
c
e
a
(Back) Return to previous menu. Exit menu. Press and hold the button for 10 seconds to reset the Wi-Fi module of soundbar to factory settings.
Prepare the Remote Control •
The provided Remote Control allows the unit to be operated from a distance.
•
Even if the Remote Control is operated within the effective range 19.7 feet (6m), remote control operation may be impossible if there are any obstacles between the unit and the remote control.
If the Remote Control is operated near other products which generate infrared rays, or if other remote control devices using infra-red rays are used near the unit, it may operate incorrectly. Conversely, the other products may operate incorrectly.
First-time use: The unit has a preinstalled lithium CR2025 battery. Remove the protective tab to activate the remote control battery.
Replace the Remote Control Battery The remote control requires a CR2025, 3V Lithium battery.
1 2 3
1
Use tools (such as coin batteries/coins) to catch the groove of the battery box cover and turn counter-clockwise to (unlock).
•
If the batteries leak, wipe away the leakage inside the battery compartment and replace the batteries with new ones.
•
Do not use any batteries other than those VSHFLÀHG
•
Do not heat or disassemble batteries.
•
1HYHUWKURZWKHPLQÀUHRUZDWHU
•
Do not carry or store batteries with other metallic objects. Doing so could cause batteries to short circuit, leak or explode.
•
Never recharge a battery unless it is FRQÀUPHGWREHDUHFKDUJHDEOHW\SH
Placement Place the subwoofer at least 1 meter (3 feet) away from your Soundbar, and ten centimeters away from the wall. For best results, place your subwoofer as shown below.
Remove the old battery, which is located in the lid, place the new CR2025 battery and pay attention to the correct polarity (+/-). Use the tools to catch the groove of the battery compartment cover and turn clockwise to (lock), secure it into the remote control. 2
3
Precautions Concerning Batteries •
When the Remote Control is not to be used for a long time (more than a month), remove the battery from the Remote Control to prevent it from leaking.
9
English
•
» You can use the wall mount template provided for helping the drilling holes position on the wall
Wall mount
» Secure the dowels and screws in the holes.
Note • Improper wall mounting may result in accident, injury or • • • •
damage. If you have any query, contact Consumer Care in your country. Before wall mounting, make sure the wall can support the weight of your Soundbar. Before wall mount, you need not remove the rubber feet at the bottom of the Soundbar, otherwise the UXEEHUIHHWFDQQRWEHÀ[HGEDFN Depending on the type of wall mounting your Soundbar, make sure that you use screws of a suitable length and diameter. Please check whether the USB port on the back of the Soundbar is connected to a USB device. If it is found that the connected USB device affects the wall-mount, you need to use another USB device of the appropriate size.
2
Remove the screws (x4) from the main unit. » Attach the wall brackets (x2) to the main unit with the screws removed from the main unit.
3
Hang the Soundbar on the fastening screws.
3.5-4mm/0.14”-0.16”
Screw length/diameter
4mm/ 0.16”
3.5-4mm >25mm/0.98”
4mm
1
Suggested wall mounting height
1
Drill 2 parallel holes (Ø 3-8mm each according to wall type) on the wall. » The distance between the holes are: • 856mm / 33.7” (TAB8405 / TAB8505) • 1017mm / 40” (TAB8805) • 1076mm / 42” (TAB8905)
10
3
2
m/
6m
107
> 25mm
/2.0"
mm
~50
42"
This section helps you connect your Soundbar to a TV and other devices, and then set it up. For information about the basic connections of your Soundbar and accessories, see the quick start guide.
Note • The full Dolby Atmos experience is only available when •
the Soundbar is connected to the source via a HDMI 2.0 cable. The Soundbar will still function when connected via other methods (such as a Digital Optical cable) but these are unable to support all of the Dolby features. Given this, our recommendation is to connect via HDMI, in order to ensure full Dolby support.
Note • )RULGHQWLÀFDWLRQDQGVXSSO\UDWLQJVVHHWKHW\SHSODWH •
at the back or bottom of the product. Before you make or change any connections, make sure that all devices are disconnected from the power outlet.
Dolby Atmos® Dolby Atmos gives you Immersive listening experience by delivering sound in three dimensional space, and all the richness, clarity, and power of Dolby sound. For more information, please visit dolby.com/ technologies/dolby-atmos
For using Dolby Atmos®
Connect to HDMI Socket Some 4K HDR TVs require the HDMI input or picture settings to be set for HDR content reception. For further setup details on HDR display, please refer to the instruction manual of your TV.
Option 1: eARC/ARC (Audio Return Channel) Your Soundbar supports HDMI with Audio Return Channel (eARC/ARC). If your TV is HDMI ARC compliant, you can hear the TV audio through your Soundbar by using a single HDMI cable.
Dolby Atmos® is available only in HDMI ARC/ eARC mode. For the details of the connection, please refer to “HDMI Connection”.
1 2 3
HDMI OUT (eARC/ARC)
To use Dolby Atmos® in HDMI 1 /HDMI 2 / HDMI ARC mode, your TV has to support Dolby Atmos®. Make sure that “No Encoding” is selected for bitstream in the digital audio output of the connected external device (e.g. Blu-ray DVD player, TV etc.). While entering Dolby Atmos / Dolby Digital / PCM format, the soundbar will show DOLBY ATMOS / DOLBY AUDIO / PCM AUDIO / DOLBY SURROUND.
HDMI (ARC)
1
2
On your TV, turn on HDMI-CEC operations. For details, see the TV user manual. • The HDMI ARC connector on the TV might be labeled differently. For details, see the TV user manual. Using a High Speed HDMI cable, connect the HDMI OUT (eARC/ARC)-TO TV connector on your Soundbar to the HDMI ARC connector on the TV. 11
English
3 Connect
1
Note • Your TV must support the HDMI-CEC and ARC
function. HDMI-CEC and ARC must be set to On.
• The setting method of HDMI-CEC and ARC may differ •
depending on the TV. For details about ARC function, please refer to your TV owner’s manual. Make sure to use the HDMI cables can support the ARC function.
Using an optical cable, connect the OPTICAL connector on your Soundbar to the OPTICAL OUT connector on the TV or other device. • The digital optical connector might be labeled SPDIF or SPDIF OUT.
Connect to AUX Socket Option 2: Standard HDMI If your TV is not HDMI ARC-compliant, connect your soundbar to the TV through a standard HDMI connection.
HDMI OUT (eARC/ARC)
a. •
Blu-ray Player / DVD Player / Recorder / Set-top Box...
HDMI 1 / HDMI 2
Use a 3.5mm to 3.5mm audio cable Use a 3.5mm to 3.5mm audio cable (not included) to connect the TV’s headphone socket to the AUX socket on the unit.
AUX
HDMI OUT
Headphone (3.5mm ) AUDIO OUT
TV TV HDMI IN
1 2
Use an HDMI cable to connect the soundbar’s HDMI IN (1 or 2) socket to your external devices (e.g. games consoles, DVD players and blu ray). Use an HDMI cable to connect the soundbar’s HDMI OUT (eARC/ARC) socket to the TV’s HDMI IN socket.
Connect to Optical Socket OPTICAL
OPTICAL OUT
12
AUX
L R AUDIO OUT
b. •
Use a RCA to 3.5mm audio cable Use a RCA to 3.5mm audio cable (not included) to connect the TV’s audio output sockets to the AUX socket on the unit.
•
•
1 2
Before connecting the AC power cord, ensure you have completed all other connections.
LED State
Status
Fast blink
Subwoofer in pairing mode
Constant on
Connected / Pairing successful
5LVNRISURGXFWGDPDJHEnsure that the power supply voltage corresponds to the voltage printed on the back or the underside of the unit.
Slow blink
Connection / Pairing Failed
Connect the mains cable to the AC~ Socket of the unit and then into a mains socket Connect the mains cable to the AC~ Socket of the subwoofer and then into a mains socket. For EU or
For UK
Tips • Do not press Pair button on the rear of the subwoofer, except for manual pairing.
Manual Pairing If no audio from the wireless subwoofer can be heard, manually pair up the subwoofer.
1
1
AC~
2
For EU or For UK
2
3
*
English
» Determine the status based on the wireless subwoofer indicator.
Connect to Power
Power cord quantity and plug type vary by regions.
3 4
Pair up with the subwoofer Automatic Pairing Plug the Soundbar and the subwoofer into the mains sockets and then press on the unit or remote control to switch the unit to ON mode. The subwoofer and Soundbar will automatically pair. SoundBar
5
Unplug both units from the mains sockets again, then plug them in again after 3 minutes. Press and hold the Pair button on the rear of the subwoofer for 5 seconds. » The Pair indicator on the subwoofer will rapidly blink. Press and hold for 5 seconds on the unit or remote control to switch the unit to ECO STANDBY mode Then press on the unit or remote control to switch the unit ON. » The Pair indicator on the subwoofer will become solid when successful. If the Pair indicator still keeps blinking, repeat step 1-3. Tips
• The subwoofer should be within 6 m of the Soundbar in an open area (the closer the better).
• Remove any objects between the subwoofer and the Soundbar.
• If the wireless connection fails again, check if there is a
FRQÁLFWRUVWURQJLQWHUIHUHQFHHJLQWHUIHUHQFHIURP an electronic device) around the location. Remove WKHVHFRQÁLFWVRUVWURQJLQWHUIHUHQFHVDQGUHSHDWWKH above procedures.
13
Connect to Wi-Fi (Wireless Operation) (For iOS and Android version) By connecting this unit and mobile phones, tablets (such as iPad, iPhone, iPod touch, Android phones, etc.) to the same Wi-Fi network, you can then use the Philips Sound app powered by DTS Play-Fi to control the VRXQGEDUWROLVWHQWRDXGLRÀOHV
1 2
Note
For iOS version only Wi-Fi network used by iPhone should be switched temporarily to Play-Fi device AP and restart Philips Sound APP to complete the product’s Wi-Fi setup. See the steps below: • Go to Settings.
• Select Wi-Fi setting.
• Select the Play-Fi device
• Return to Philips Sound
Connect your phone or tablet to the same Wi-Fi network that you want to connect your soundbar Download and install the Philips Sound app powered by DTS Play-Fi on a phone or tablet.
in the Wi-Fi set up
App to continue the set up.
1
2
•
3
Make sure your router is turned on and Philips Sound Philips Sound working properly. Devices Set Up Play-Fi Device
Press and hold (Wi-Fi) button located at the back cabinet for 8 sec to trigger the Wi-Fi connection. » Until the speaker make a second tone Philips Sound Philips Sound and then release the button. Choose Name
34
5
14
Bathroom . . . . Custom Name
Set Up
6
Update Available
Download & Update
Wait until the Wi-Fi light indicator on front cabinet goes from a fast blink to a slow pulse.When it begins slow pulsing indicating that the speaker is entering the Wi-Fi setup mode. Launch the Philips Sound App powered by DTS Play-Fi. Follow the instructions in the App to connect this product to your Wi-Fi network.
7
After successful Wi-Fi connection, the Wi-Fi light indicatar on the front cabinet will stop pulsing and turn solid. Once you set up this product on your Wi-Fi network, you can control it from any smartphone or tablet on the same network. » When using the APP to play music, the display panel will show PLAY-FI. After connection, you can change the device name. There are several names to choose from or create your own by choosing Custom Name at the end of the name list. Otherwise, it follows the default name.
After connection, this product may perform a software update. Upgrade to the latest software when LWLV\RXUÀUVWWLPHVHWXS7KHVRIWZDUH upgrade may take several minutes. Do not unplug your speaker, turn off your device, or leave the network during the update.
AirPlay setup Use AirPlay to set up the Wi-Fi connection of iOS device (iOS7 or later) and soundbar.
1 2
iOS device: Settings > Wi-Fi > select home network [Play-Fi device (xxxxxx)] Launch the Philips Sound App powered by DTS Play-Fi. Follow the instructions in the App to connect this product to your Wi-Fi network. » After successful Wi-Fi connection, the Wi-Fi light indicatar on the front cabinet will stop pulsing and turn solid. Once you set up this product on your Wi-Fi network, you can control it from any smartphone or tablet on the same network. » When using the APP to play music, the display panel will show PLAY-FI.
3
4
After connection, you can change the device name. There are several names to choose from or create your own by choosing Custom Name at the end of the name list. Otherwise, it follows the default name. After connection, this product may perform a software update. Upgrade to the latest software when LWLV\RXUÀUVWWLPHVHWXS7KHVRIWZDUH upgrade may take several minutes. Do not unplug your speaker, turn off your device, or leave the network during the update.
Note • After connection, the product may perform a software •
•
update. Upgrade is required after initial set up. Without the upgrade, not all product features can be available. :KHQWKHÀUVWWLPHVHWXSLVQRWVXFFHVVIXOKROG down the Wi-Fi button on soundbar for 8 seconds until the second tone can be heard and the Wi-Fi light is changed to slow pulse. Reset the Wi-Fi connection, restart the app and start the set up again. If you want to change from one network to another, you need to set up the connection again. Press hold down the (Wi-Fi) button on the soundbar for 8 seconds to reset the Wi-Fi connection.
WPS mode If your router has Wi-Fi Protected Setup (WPS), you can set up the connection without entering a password.
1 2
3
Press and hold the Wi-Fi button for 4 seconds. You will hear a tone and the Wi-Fi light will begin in double blink. Press the WPS button on your router. The button is normally marked with this WPS logo.
WPS
Follow the instruction in Philips Sound App powered by DTS Play-Fi to start the pairing. Note
• WPS is not a standard feature on all routers. If your •
router does not have WPS then use Standard Wi-Fi Setup. Press the (Wi-Fi) button once if you want to exit the WPS mode or it will automatically exit after 2 minutes.
15
English
8
4 Use your Soundbar
Select Modes 1
This section helps you use the Soundbar to play audio from connected devices. Before you start • Make the necessary connections described in the quick start guide and the user manual. • Switch the Soundbar to the correct source for other devices.
Turn ON and OFF •
:KHQ\RXÀUVWFRQQHFWWKHXQLWWRWKH main socket, the unit will be in STANDBY mode. The STANDBY indicator will light up white. Power Action State On Press the Semi button Standby once Press and hold Eco Standby button 5 seconds
Function
• Follow source state • Wi-Fi is still on. • It still supports Play-Fi and
» Play-Fi is not an optional source. Play-Fi needs to be directly controlled by APP.
Adjust the Volume Adjust the Soundbar’s Volume
1
Press +/- (Volume) to increase or decrease a volume level. • To mute sound, press Mute. • To restore the sound, press Mute again or press Vol+/Vol- (Volume).
Adjust the Subwoofer’s Volume
1
Press +/- (subwoofer) to increase or decrease the subwoofer’s volume level.
Airplay2.
• Wi-Fi is off. • The product enters the lower •
power consumption mode. Restarting the system will take a relatively longer time.
Auto Standby The unit automatically turns to Standby mode after about 15 minutes if the TV or the external unit is disconnected (or USB, BT, Play-Fi function bit playback pause), switched off. • To switch the unit off completely, remove the mains plug from the mains socket. • Please turn the unit off completely to save energy when not in use.
16
Press the button repeatedly on the unit or on the remote control to select the AUX, OPTICAL, HDMI eARC/ARC, HDMI 1, HDMI 2, BT, USB mode. » The selected mode will show on the display.
Dolby sound mode Experience an immersive audio experience with Dolby sound modes.
1
Press button on the remote control to turn Dolby mode on or off. • On: Create a Dolby listening experience. • Off: Two-channel stereo sound. Ideal for listening to music.
CENT (CENTER)
1
(TAB8805, TAB8905 only) Adjust the Center Channel Volume » CTR -5 ~ CTR +5 » By default, the center channel volume is set to 0.
2
TOP (TAB8905 only) Adjust the Top Channel Volume » TOP +5 ~ TOP –5
3
» By default, the top channel sound is set to 0.
DIM
4
Set display brightness. » DIM 03, DIM 02, DIM 01 » By default, the dimmer is set to DIM 03.
DISPLAY Set to turn off the display automatically (except the Wi-Fi LED indicator) after 3 seconds of idle when no user operation. » ON: Set to display on
5
» OFF: Set to display off » By default, the display is set to ON.
KEY TONE Turn On/off the key tone » ON: Set to ON
On the Bluetooth device, switch on Bluetooth, search for and select Philips TAB8505 to start connection (see the user manual of the Bluetooth device on how to enable Bluetooth). Wait until you hear the voice prompt from the Soundbar. » If the successfully connected, BT is displayed on the display panel. 6HOHFWDQGSOD\DXGLRÀOHVRUPXVLFRQ\RXU Bluetooth device. • During play, if a call is coming, music play is paused. Play resumes when the call ends. • If your Bluetooth device supports $95&3SURÀOHRQWKHUHPRWHFRQWURO you can press / to skip to a track, or press to pause/resume play. To exit Bluetooth, select other source. • When your switch back to Bluetooth mode, Bluetooth connection remains active. • If you want to connect your Soundbar with another Bluetooth device, press and hold on the remote control to disconnect the currently connected Bluetooth device. Note
» OFF: Set to OFF » By default, the key tone is set to off.
Press the button repeatedly on the unit or on the remote control to switch the Soundbar to Bluetooth mode. » NO BT is displayed on the display panel.
• $%OXHWRRWKGHYLFHZKLFKVXSSRUWV%OXHWRRWKSURÀOH
A2DP, AVRCP and with Bluetooth version as 4.2 + EDR.
• The maximum operational range between the
Bluetooth Operation Through Bluetooth, connect the Soundbar with your Bluetooth device (such as an iPad, iPhone, iPod touch, Android phone, or laptop), and then \RXFDQOLVWHQWRWKHDXGLRÀOHVVWRUHGRQWKH device through your Soundbar speakers. 18
• •
Soundbar and a Bluetooth device is approximately 10 meters (30 feet). Compatibility with all Bluetooth devices is not guaranteed. The music streaming may be interrupted by obstacles between the device and Soundbar, such as wall, metallic casing that covers the device, or other devices nearby that operate in the same frequency.
Ensure that the unit is connected to the TV or audio device.
1 2 3
USB Operation Enjoy audio on a USB storage device, such as an 03SOD\HUDQG86%ÁDVKPHPRU\HWF
1
Insert the USB device.
Press the button repeatedly on the unit or on the remote control to select the AUX, OPTICAL, HDMI eARC/ARC, HDMI 1, HDMI 2 mode. Operate your audio device directly for playback features. Press the VOL +/– buttons to adjust the volume to your desired level. Tip
2
Press the button repeatedly on the unit or on the remote control to select the USB mode.
• While in OPTICAL/HDMI ARC mode, if there’s no
•
• •
• •
sound output from the unit and the status Indicator ÁDVKHV\RXPD\QHHGWRDFWLYDWHPCM or Dolby Digital Signal output on your source device (e.g. TV, DVD or Blu-ray player). The unit may not be able to decode all digital audio formats from the input source. In this case, the unit will mute. This is NOT a defect. Ensure that the audio setting of the input source (e.g. TV, game console, DVD player, etc.) is set to PCM or Dolby Digital (Refer to the user manual of the input source device for its audio setting details) with HDMI 1 / HDMI 2 / HDMI ARC / optical input. In HDMI mode, when the DOLBY ATMOS audio format is entered, the Soundbar display shows DOLBY ATMOS. When the DOLBY DIGITAL audio format is entered, if surround sound is turned on, the whispering wall display will display DOLBY SURROUND, if surround sound is turned off, it will display DOLBY AUDIO. When the PCM audio format is entered, the Soundbar display shows PCM AUDIO. When entering non-PCM or DOLBY DIGITAL audio formats, if there’s no sound output from the unit and the display show ERROR.
3
During playback: Start, pause or resume play. Skip to the previous or next track.
/ Tips
• This product may not be compatible with certain types of USB storage devices.
• If you use a USB extension cable, USB hub, or USB • • • •
Multifunctional card reader, the USB storage device may not be recognized. Do not remove the USB storage device while reading ÀOHV The unit can support USB devices with up to 32 GB of memory. This unit can play MP3 / WAV / FLAC. Support a USB port: 5V 500mA.
Listen to Spotify Use your phone, tablet or computer as a remote control for Spotify. Go to spotify.com/ connect to learn how.
19
English
AUX / OPTICAL / HDMI ARC Operation
Upgrade Firmware To get the best features and support, update \RXUSURGXFWZLWKWKHODWHVWÀUPZDUHYHUVLRQ Option 1: 8SGDWHÀUPZDUHYLD3KLOLSV6RXQG$SS (Settings > PS Fine Tune) 7KHÀUPZDUHIRU0&8DQG'63FDQEH upgraded to the latest version via Philips Sound App powered DTS Play-Fi. Please go to settings menu and select PS Fine Tune option to check it out. If the upgrade is released, the upgraded icon can be pressed to proceed automatically. Once this product is connected to Wi-Fi, it can UHFHLYHRYHUWKHDLUÀUPZDUHXSGDWH$OZD\V XSJUDGHZLWKWKHODWHVWÀUPZDUHYHUVLRQWR improve the performance of this product. Option 2: 8SGDWHÀUPZDUHYLD86%
1 2 3
20
&KHFNLIWKHUHLVWKHODWHVWÀUPZDUH version on www.philips.com/support. Search for your model and click on “Software and drivers”. 'RZQORDGWKHÀUPZDUHLQWRD86%ÁDVK drive. )ROORZWKHLQVWUXFWLRQIRUWKHÀUPZDUH upgrade.
Note • 6SHFLÀFDWLRQVDQGGHVLJQDUHVXEMHFWWRFKDQJHZLWKRXW notice.
Bluetooth / Wireless • • • •
%OXHWRRWK3URÀOHV$'3$95&3 Bluetooth Version: 4.2 + EDR Frequency Band/Output Power: 0+]a0+]G%P 2.4G Wireless Frequency Range / Output 3RZHU0+]a0+]G%P
Network supported •
WiFi IEEE 802.11a/b/g/n/ac Wireless Frequency Band (Wi-Fi) / Radio Frequency Power Transmitted 2.4G Wi-Fi: 2400 MHz~2483.5 MHz / G%P
Subwoofer • • • • • • • • •
Main unit • • • • • • • • • • •
Power Supply: 100-240V~ 50/60Hz MAX Output Power by speaker: 30W x 2 Power Consumption: 25 W Standby Consumption: < 0.5 W USB: 5V 500mA Frequency Response: 150Hz - 20KHz Audio Input Sensitivity: 500mV 6SHDNHUV,PSHGDQFHƙ[ Dimension (W x H x D ): 900 x 57 x 110 mm Weight: 2.4 kg Operating Temperature: 0°C - 45°C
Power Supply: 100-240 V~, 50-60 Hz Output Power: 60 W Power Consumption: 20 W Standby Power Consumption: < 0.5 W Frequency Response: 35Hz - 150Hz ,PSHGDQFHƙ Dimensions (W x H x D): 120 x 403 x 300 mm Weight: 4.8 kg Operating Temperature: 0°C - 45°C
Remote control • •
Distance/Angle: 6m/30° Battery Type: CR2025
Supported audio formats •
HDMI eARC/ARC Dolby Digital, Dolby Digital plus, Dolby True HD, Dolby Atmos®, LPCM 2ch/Mch , Dolby MAT.
•
HDMI IN1/ HDMI IN2 Dolby Digital, Dolby Digital plus, Dolby True HD, Dolby Atmos®, LPCM 2ch/Mch , Dolby MAT.
•
OPTICAL Dolby Digital, Dolby Digital plus, LPCM 2ch
•
BLUETOOTH SBC
•
USB MP3 / WAV / FLAC
•
Video Video Enhancement: 4K Video Passthrough, Dolby Vision, HDR10, HDR10+,
5.1G Wi-Fi: 5150 MHz~5350 MHz / G%P 5.8G Wi-Fi: 5725 MHz~5850 MHz / G%P
English
5 Product specifications
21
6 Troubleshooting
• •
Warning • Risk of electric shock. Never remove the casing of the product.
To keep the warranty valid, never try to repair the product yourself. If you have problems using this product, check the following points before you request service. If you still have a problem, get support at www.philips.com/support.
Main unit The buttons on the main unit do not work. • Disconnect form the power supply for a few minutes,then connect again. No power • Ensure that the AC cord is properly connected. • Ensure that there is power at the AC outlet. • Press standby button on the remote control or Soundbar to turn the Soundbar on.
Sound No sound from the soundbar speaker. • Connect the audio cable from your soundbar to your TV or other devices. However, you do not need a separate audio connection when: - the soundbar and TV are connected through HDMl ARC connection, or - a device is connected to the HDMI IN connector on your soundbar. • On the remote control, select the correct audio input. • Make sure that the soundbar is not muted. • Reset this product to its factory settings (see ‘Apply factory settings). No sound from the wireless subwoofer. • Manually connect the subwoofer to the main unit. 22
•
• •
Increase the volume. Press Volume Up on the remote control or on the Soundbar. When using either of the Digital input, if there is no audio: - Try setting the TV output to PCM or - Connect directly to your Blu-ray/other source, some TVs do not pass through digital audio. Your TV may be set to variable audio RXWSXW&RQÀUPWKDWWKHDXGLRRXWSXW setting is set to FIXED or STANDARD, not VARIABLE. Consult your TV’s user manual for more detailed information. If using Bluetooth, ensure that the volume on your source device is turned up and that the device is not muted. When the playback freezes and there is no sound in Wi-Fi mode, please check whether your home network is normal.
Distorted sound or echo. • lf you play audio fromTV through this product, make sure that theTV is muted. Audio and video are not synchronized. • Press to synchronize the audio with the video.
Bluetooth A device cannot connect with the soundbar. • The device does not support the FRPSDWLEOHSURÀOHVUHTXLUHGIRUWKH soundbar. • You have not enabled the Bluetooth function of the device. See the user manual of the device on how to enable the function. • The device is not correctly connected. Connect the device correctly. • The soundbar is already connected with another Bluetooth device. Disconnect the connected device, then try again. Quality of audio play from a connected Bluetooth device is poor. • The Bluetooth reception is poor. Move the device closer to the soundbar, or remove any obstacle between the device and the soundbar.
Wi-Fi Wi-Fi Connection cannot be established. • Check the availability of WLAN network on the router. • Place the Wi-Fi router closer to the unit. • Make sure the password is correct. • Check the WLAN function or reboot the modem and Wi-Fi router.
Dolby Atmos Cannot achieve outstanding Dolby Atmos effects. • For non-HDMI connections (such as use of USB, Bluetooth, OPTICAL or AUDIO IN), limited height surround effects are generated. See the section of ‘Dolby Atmos’ about how to achieve best Dolby Atmos effects.
Play-Fi
Remote control does not work • • • • •
Before you press any playback control EXWWRQÀUVWVHOHFWWKHFRUUHFWVRXUFH Reduce the distance between the remote control and the unit. Insert the battery with its polarities (+/-) aligned as indicated. Replace the battery. Aim the remote control directly at the sensor on the front of the unit.
This is a 15 mins power off function, one of the ERPII standard requirement for saving power •
When the unit’s external input signal level is too low, the unit will be turned off automatically in 15 minutes. Please increase the volume level of your external device.
The subwoofer is idle or the indicator of subwoofer do not light up •
Please unplug power cord from the mains sockect, and plug it in again after 3 minutes to reset the subwoofer.
Cannot discover the Play-Fi supported devices from the app. • Make sure the device is connected to the Wi-Fi. Cannot play Play-Fi music. • Certain network service or contents available through the device may not be accessible in case the service provider terminates its service. • :KHQWKHÀUVWWLPHVHWXSLVQRWVXFFHVVIXO close the Philips Sound app powered by DTS Play-Fi. Restart the app. • When the speaker was set as Stereo Pairs or Surround Sound, the speaker need to be disconnected in the App before use separately.
23
English
,FDQ·WÀQGWKH%OXHWRRWKQDPHRIWKLVXQLWRQ my Bluetooth device • Ensure the Bluetooth function is activated on your Bluetooth device. • Re-pair the unit with your Bluetooth device.
Trademarks:
For DTS patents, see http://patents.dts. com. Manufactured unde license from DTS, Ins. (for companies headquartered in the U.S./Japan/ Taiwan) or under license from DTS Licensing Limited (for all other companies). DTS, PlayFi, and the DTS Play-Fi logo are registered trademarks or trademarks of DTS, Inc. in the United States and other countries. ©2020 DTS, Inc. ALL RIGHTS RESERVED.
The Wi-Fi CERTIFIED™ Logo is a registered trademark of Wi-Fi Alliance®.
Google, Google Play and Chromecast builtin are trademark of Google LLC. Google Assistant is not available in certain languages and countries.
To control this AirPlay 2 -endabled speaker, iOS 11. 4 or later is required. Use of the Works with Apple badge means that an accessory has been GHVLJQHGWRZRUNVSHFLÀFDOO\ZLWKWKHWHFKQRORJ\ LGHQWLÀHGLQWKHEDGJHDQGKDVEHHQFHUWLÀHG by trademarks of Apply Inc. ,registered in the U. S. and other countries. Apple® and AirPlay® are trademarks of Apple Inc., registered in the U.S. and other countries. 24
The Spotify Software is subject to third party licenses found here: www.spotify.com/connect/ third-party-licenses
7KHWHUPV+'0,+'0,+LJK'HÀQLWLRQ Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Dolby, Dolby Vision, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby /DERUDWRULHV&RQÀGHQWLDOXQSXEOLVKHGZRUNV Copyright © 2012-2020 Dolby Laboratories. All rights reserved.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.
6SHFLÀFDWLRQVDUHVXEMHFWWRFKDQJHZLWKRXWQRWLFH Please visit http://www.philips.com/support for the latest updates and documents. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under WKHUHVSRQVLELOLW\RI00'+RQJ.RQJ+ROGLQJ/LPLWHGRURQHRILWVDIÀOLDWHVDQG MMD Hong Kong Holding Limited. is the warrantor in relation to this product.
Similar documents
-
Philips TAB8505
- 4.3 MB - Audio, Loudspeaker, Philips, Philips TAB8505
-
Philips TAB8505
- 4.2 MB - Audio, Loudspeaker, Philips, Philips TAB8505
-
Philips TAB8505
- 4.3 MB - Audio, Loudspeaker, Philips, Philips TAB8505
-
Philips TAB8505
- 2.2 MB - Audio, Loudspeaker, Philips, Philips TAB8505
-
Philips Philips P9BLK
- 7.7 MB - Audio, Loudspeaker, Philips, Philips Philips P9BLK
-
Philips Philips DTM3170
- 1.2 MB - Audio, Midi set, Philips, Philips Philips DTM3170
-
Philips Philips DTM3170
- 1.2 MB - Audio, Midi set, Philips, Philips Philips DTM3170
-
Philips Philips DTM3170
- 3.7 MB - Audio, Midi set, Philips, Philips Philips DTM3170
-
Philips Philips DTM3170
- 1.2 MB - Audio, Midi set, Philips, Philips Philips DTM3170
-
Philips Philips AD7050W-10
- 4.4 MB - Audio, Loudspeaker, Philips, Philips Philips AD7050W-10
-
Philips Philips Fidelio A5
- 7.9 MB - Audio, Loudspeaker, Philips, Philips Philips Fidelio A5
-
Philips Philips AD7050W-10
- 4.5 MB - Audio, Loudspeaker, Philips, Philips Philips AD7050W-10
-
Philips Philips Fidelio A5
- 7.9 MB - Audio, Loudspeaker, Philips, Philips Philips Fidelio A5
-
Philips Philips Fidelio A5
- 7.9 MB - Audio, Loudspeaker, Philips, Philips Philips Fidelio A5
-
Philips Philips Fidelio A5
- 6.3 MB - Audio, Loudspeaker, Philips, Philips Philips Fidelio A5
-
Philips Philips AD7050W-10
- 4.5 MB - Audio, Loudspeaker, Philips, Philips Philips AD7050W-10
-
Philips Philips DTM3170
- 1.2 MB - Audio, Midi set, Philips, Philips Philips DTM3170
-
Philips Philips DTM3170
- 1.3 MB - Audio, Midi set, Philips, Philips Philips DTM3170
-
Philips Philips DTM3170
- 1.3 MB - Audio, Midi set, Philips, Philips Philips DTM3170
-
Philips Philips Fidelio A5
- 1.2 MB - Audio, Loudspeaker, Philips, Philips Philips Fidelio A5
-
Philips Philips Fidelio A5
- 7.9 MB - Audio, Loudspeaker, Philips, Philips Philips Fidelio A5
-
Philips Philips Fidelio A5
- 7.9 MB - Audio, Loudspeaker, Philips, Philips Philips Fidelio A5
-
Philips Philips AD7050W-10
- 4.5 MB - Audio, Loudspeaker, Philips, Philips Philips AD7050W-10
-
Philips Philips DTM3170
- 1.3 MB - Audio, Midi set, Philips, Philips Philips DTM3170