JL Audio C5-570
* The preview only show first 10 pages of manuals. Please download to view the full documents.
Loading preview... Please wait.
5-inch x 7-inch (125 x 180 mm) 2-Way Component System
Thank you for choosing a JL Audio Evolution™ C5 Component System for your automotive sound system. These Evolution™ Speakers have been designed and manufactured to exacting standards in order to ensure years of musical enjoyment in your vehicle. For maximum performance, we highly recommend that you have your new speakers installed by an authorized JL Audio dealer. Your authorized dealer has the training, expertise and installation equipment to ensure optimum performance from this product. Should you decide to install the speakers yourself, please take the time to read this manual thoroughly so as to familiarize yourself with its installation requirements and setup procedures. If you have any questions regarding the instructions in this manual or any aspect of your amplifier’s operation, please contact your authorized JL Audio dealer for assistance. If you need further assistance, please call the JL Audio Technical Support Department at (954) 443-1100 during business hours.
D A B A
Woofer Physical Dimensions Frame Outer Diameter (A)
5.47 x 7.68 in. / 139.0 x 195.1 mm
Magnet Outer Diameter (B)
3.54 in. / 90.0 mm
Mounting Hole Diameter (C)
Mounting Depth (D)
2.4 in. / 61 mm
Tweeter Fixture Physical Dimensions
Fixture Outer Diameter (A)
1.75 in. / 44.5 mm
1.61 in. / 40.9 mm
Fixture Mounting Hole Diameter (B)
1.50 in. / 38.1 mm
Fixture Mounting Depth (C)
0.56 in. / 14.2 mm
Tweeter Frontal Protrusion (D)
0.36 in. / 9.1 mm
0.87 in. / 22.1 mm
Crossover Network Physical Dimensions Height (A)
4.72 in. / 119.9 mm
3.36 in. / 85.3 mm
1.44 in. / 36.6 mm
2 | JL Audio - C5-570 Owner’s Manual
C5-570 SPECIFICATIONS Woofers: Cast Alloy Frame, Patented Elevated Frame Cooling
Included Components and Parts:
(U.S. Patent #6,219,431 & #6,229,902), DMA-Optimized Motor
• Two C5-570cw 5x7-inch (125 x 180 mm) Woofers
System, Mineral-Filled Polypropylene Cone, Butyl Rubber
• Two C5-075ct 0.75-inch (19 mm) Tweeters
Surround, 1-in. / 25 mm Voice Coil, Kapton® Former, Low-
• Two C5-570-XO Crossover Networks
Profile, Symmetrical Roll Spider, Ferrite Magnet
• Two Flush-Mount Tweeter Fixtures • Two Surface-Mount Tweeter Fixtures
Tweeters: 0.75 in. / 19 mm Silk Soft Dome
• Two Metal Spring Clips for Tweeter Fixtures
RSR Variable-Angle Flush-Mount System, Ferrofluid Cooling
• Two Woofer Spacer Gaskets
and Damping, Neodymium Magnet
• Two Self-Adhesive JL Audio Nameplates for Grilles • Butyl Adhesive Putty for Woofer Grilles
Crossover Networks: 2-way network with 1st order
• Twelve #8 x 1.25 inch (32 mm) Sheet Metal Screws
low-pass and 2nd order high-pass circuit, premium Mylar®
• Four #6 x 1-inch (25 mm) Sheet Metal Screws
capacitors, air-core inductors, 4-position adjustable tweeter
• Two 1.18-inch (30 mm) Machine Screws
output level, 3-position midrange presence control,
• Eight Mounting Clips for Woofer Mounting
Polyswitch tweeter protection
• Two 6.4 mm Female Crimpable Connectors • Four 4.7 mm Female Crimpable Connectors
Continuous Power Handling: 75 Watts (RMS Method)
• Two 2.8 mm Female Crimpable Connectors
Peak Music Power: 225 Watts
• Four 2.8 mm Male Crimpable Connectors
Recommended Power Range: 25-150 Watts (RMS)
• Twelve Crimpable Spade Connectors
Frequency Response: 48 Hz - 25 KHz (± 3 dB) Efficiency @ 1W/1m: 90.5 dB @ 1W/1m Nominal Impedance: 4 ohms
Due to ongoing product development, all specifications are subject to change without notice.
GETTING STARTED •Turn off the audio system. It is also advisable to disconnect the negative (–) terminal of your vehicle’s battery whenever performing installation work. •Before cutting, drilling or inserting any screw, check clearances on both sides of the planned mounting surface. Also check for any potential obstacles, such as window tracks and motors, wiring harnesses, etc. Check both sides of the vehicle, many vehicles are not symmetrical! •Always wear protective eyewear. CROSSOVER NETWORK INSTALLATION The crossover networks supplied with your C5 System should be installed in a dry location inside your vehicle. DO NOT INSTALL THEM INSIDE OF A DOOR! Doors often get wet on the inside, which can damage your crossover networks and could potentially damage your entire sound system. The crossovers can be screwed into a solid surface via two holes located under the protective cover of the case. To access these holes, simply squeeze the sides of the cover while gently pulling the cover away from the base. Make sure that your mounting location will not cause damage to wiring, fuel lines, brake lines or any other vital component of your vehicle. Once you have screwed the case in and made your connections, snap the protective cover back into place.
It is absolutely vital that your component system is connected as shown in this manual. Failure to connect the system as shown may result in damage to your speakers which is NOT covered under warranty. Do not substitute different crossover networks into your C5 System. Do not use crossover networks intended for different C5 models.
4 | JL Audio - C5-570 Owner’s Manual
TWEETER PROTECTION The C5 crossover networks are equipped with an advanced electronic tweeter protection circuit designed to minimize the possibility of tweeter failure. This electronic device monitors current going to the tweeter and will disconnect the tweeter from the signal when it senses overload. Should this occur while listening to the audio system, simply reduce the volume for a few seconds and the protection circuit will reset itself automatically. CROSSOVER NETWORK ADJUSTMENT The crossover networks have been designed to allow tonal adjustments to the upper midrange response and tweeter level. These adjustments make it possible to fine-tune your system to suit your listening preferences and to compensate for various speaker mounting applications.
ADJUSTABLE MIDRANGE PRESENCE Your C5 crossover networks provide a unique midrange presence control, located under the cover. The midrange presence is selectable via a set of pins and allows for three settings. These settings affect the amplitude of the upper midrange response of the C5 component woofer. We recommend that you begin your listening in the “REF” (Reference) and adjust up or down as needed to compensate for mounting location, orientation or personal taste.
ADJUSTABLE TWEETER LEVEL C5 crossover networks also provide four levels of tweeter adjustability designed to compensate for different mounting locations, vehicle interiors and personal taste. These levels are selectable via a set of pins located under the clear cover of each crossover case. We recommend that you begin listening in the “REF” (Reference) position. To find the optimum tonal balance in your installation, experiment with alternate tweeter level settings by moving the pins. It is safe to switch jumpers while the system is playing.
SPEAKER PLACEMENT CONSIDERATIONS A component system gives you the ability to place the woofer and tweeter separately in your vehicle interior. This can be good or bad, depending on how it’s done. As a general rule, the tweeters should be placed relatively close to the woofers for best tonal balance and most coherent imaging (the closer, the better). Any separation greater than 8 inches (20 cm) is likely to result in degraded sound quality. Avoid placing tweeters where they will be blocked by objects in the interior of the car (including seated occupants). When selecting a mounting location, look at both sides of the car to make sure that this location is clear on both sides. You can always experiment with tweeter placement before committing to a final mounting location. Simply connect the rest of the system and allow plenty of wire length for the tweeters. Using Velcro® or similar material, attach the tweeters in different locations until you find the one where they perform best. Woofers will usually be placed into factory speaker locations. If you have some woofer mounting flexibility, keep the following in mind: Lower mounting locations, such as the lower front corner of a door or a kick-panel provide the greatest path length distances for the sound emitted by the woofer. For this reason, they are generally more desirable than higher mounting locations. Higher mounting locations often result in extreme nearside soundstage bias which compromises the stereo listening experience.
6 | JL Audio - C5-570 Owner’s Manual
Diagram A: Less Desirable Speaker Placement
Diagram B: More Desirable Speaker Placement
!! WA RNING Double check the clearance for both speakers before proceeding. Many cars are different from one side to the other! Woofer INSTALLATION The woofers should be installed in one of the following ways depending on location: Factory Location: If you will be using the factory speaker wires, it may be necessary to change the terminations. This may be accomplished by using an adaptor plug or simply by cutting the factory connector off and using the supplied crimp connectors to terminate the speaker wires. The large connector is for the positive (+) terminal and the small connector is for the negative (–) terminal of each woofer. Keep in mind that the woofer wires must be connected to the woofer outputs of the crossovers supplied with your system as shown in the diagram on page 5. If you prefer to run new wires, refer to the “Custom Location” installation section for details. Whichever method you choose, observe correct polarity in your connections. If you are unsure about any of these issues, contact your JL Audio dealer for installation assistance. Your new speakers have been designed to install, without modifications, into most vehicles that accept a 5x7-inch (125 x 180 mm) speaker. Most factory 5x7-inch speakers use four mounting screws which will line up with the mounting holes on your woofers. A spacer gasket has been included to fine-tune speaker fitment. This gasket can be mounted on the front of the mounting flange, the back of the mounting flange or simply not be used in the installation. It is absolutely vital that the speaker frame fits into the mounting hole cleanly. This must be checked prior to tightening the screws. Do not force the frame into a hole that is too small. Do not tighten the speaker onto an uneven surface. This will damage your speakers. The speaker should also fit so that air does not leak around the mounting flange. Air leaks will cause a severe degradation in sound quality. Seal any air leaks with an automotivegrade sealant material. Use the supplied mounting clips unless the factory holes already feature threaded inserts. Hand-tighten the screws evenly.
8 | JL Audio - C5-570 Owner’s Manual
Custom Location: Run speaker wire to the desired mounting locations. If you are running wires into a door, use existing factory wiring boots whenever possible. If you are drilling new holes, file their edges and install rubber grommets into each hole. Wires should then be covered with a protective, flexible PVC sleeve and then run through the door jamb. Make sure that the wires will clear door hinges and other structures in the door. If you are unsure about any part of this process, please contact your JL Audio dealer for installation help. Double check the clearance for both speakers before proceeding. Select an even surface. Tightening a speaker onto an uneven surface can damage it. Use the supplied template to mark the desired mounting location. Mark the center and the outline of the mounting hole as well as the mounting screw positions. Before drilling or cutting on your interior panels, use a utility knife to cut any fabric, vinyl or leather from hole locations. These materials can easily be snagged by a drill or a saw, causing damage to the panel and possible bodily injury. Drill four 1/8-inch (3 mm) holes for the speaker’s mounting screws at the positions you have marked. Also drill a pilot hole in the center of the speaker mounting hole at this time. Then, using a saber saw, make the circular cut out for the speaker. File any rough edges. Insert the mounting clips with the flat side towards the speaker as shown in the Diagram C. It is absolutely vital that the speaker frame fits into the mounting hole cleanly. This must be checked prior to tightening the screws. Do not tighten the speaker onto an uneven surface! This will damage your speakers. The speaker should also fit so that no air leaks around the mounting flange. Air leaks will cause a severe degradation in sound quality. Seal any air leaks with silicone, rope caulk or similar sealant material.
A spacer gasket has been included to fine-tune speaker fitment. This gasket can be mounted on the front of the mounting flange, the back of the mounting flange or simply not be used in the installation. Connect the speaker wires, observing correct polarity, and secure the speaker and grille tray to the panel by evenly tightening by hand the provided #8 x 1.25 inch (16 mm) mounting screws. Make sure the woofer is secured so that air does not leak around the mounting flange. Air leaks will cause a severe degradation in sound quality. Seal any air leaks with an automotive-grade sealant material.
Diagram C: Factory/Custom Location Woofer Installation OPTIONS
WA R N I N G
Hand-tighten the screws evenly in a criss-cross pattern to avoid bending the speaker frame or stripping the mounting clips.
TWEETER INSTALLATION First, run speaker wires from the tweeter output of the crossover (see diagrams on page 5) to the desired tweeter mounting locations, observing the same precautions as mentioned in the woofer installation section. Terminate the wires with the supplied 2.8 mm male crimpable connectors. TWEETER FiXTURE INSTALLATION The dome tweeters supplied with your C5-570 system have been designed for maximum mounting versatility. There are two primary methods by which the tweeters can be mounted in your vehicle: Flush-Mount: For tweeter integration in a clean, unobtrusive manner, you will use the supplied flush-mount cups. This compact mounting fixture is installed using the method illustrated in Diagram E and requires a mounting hole with a diameter of 1.50 in. (38.1 mm). At least 3/4-inch (19 mm) of clearance is required behind the mounting surface of the tweeter for the spring clips and 1.18-inch machine screws used in mounting the fixture. It may be necessary in some limited depth applications to cut down the length of the machine screw, or to use a shorter screw (not supplied). Hand-tighten the machine screw until the fixture is secure. Surface-Mount: In this application, you will not need to cut large holes in your vehicle’s panels for the tweeters. You will only need to drill a hole for the wires and two smaller holes for the mounting screws. This application is useful when mounting the tweeters to a panel that has insufficient clearance behind it for the tweeter’s magnet structure. Using the fixture as a template, mark the screw hole locations and a location in the center of the fixture for the wire hole. Remove the fixture and drill pilot holes for the screws and a 1/8-inch (3 mm) for the wires. Use the supplied #6 x 1-inch sheet metal screws to secure the fixture as shown in Diagram F (hand-tighten). Run the tweeter’s wires through the hole and insert the tweeter until it snaps into place.
10 | JL Audio - C5-570 Owner’s Manual
Diagram E: Flush-Mount Tweeter Installation
Diagram F: SURFACE-Mount Tweeter Installation
Limited Warranty - Automotive Speaker Systems (USA)
JL AUDIO warrants these speakers (and crossover networks, where applicable) to be free of defects in materials and workmanship for a period of one (1) year. This warranty is not transferable and applies only to the original purchaser from an authorized JL AUDIO dealer. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty. Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. If you need service on your JL AUDIO product: All warranty returns should be sent to JL AUDIO freight prepaid through an authorized JL AUDIO dealer and must be accompanied by proof of purchase (a copy of the original sales receipt.) Direct returns from consumers or non-authorized dealers will be refused unless specifically authorized by JL AUDIO with a valid return authorization number. Warranty expiration on products returned without proof of purchase will be determined from the manufacturing date code. Coverage may be invalidated as this date is previous to purchase date. Return only defective components. If one speaker fails in a system, return only that speaker component, not the entire system. Non-defective items received will be returned freight-collect. Customer is responsible for shipping charges and insurance in sending the product to JL AUDIO. Freight damage on returns is not covered under warranty.
For Service Information in the U.S.A. please call JL Audio Customer Service: (954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone) JL Audio, Inc 10369 North Commerce Pkwy. Miramar, FL 33025 International Warranties: Products purchased outside the United States of America are covered only by that country’s distributor and not by JL Audio, Inc.
JL Audio VX400
- 281 KB - Automotive, Car Amplifier, JL Audio, JL Audio VX400
JL Audio 5
- 1012.4 KB - Automotive, Car Amplifier, JL Audio, JL Audio 5
JL Audio XD1000
- 4.2 MB - Automotive, Car Amplifier, JL Audio, JL Audio XD1000
JL Audio 1v2
- 4.2 MB - Automotive, Car Amplifier, JL Audio, JL Audio 1v2
JL Audio JX250
- 2.3 MB - Automotive, Car Amplifier, JL Audio, JL Audio JX250
JL Audio 3
- 265.9 KB - Automotive, Car Amplifier, JL Audio, JL Audio 3
JL Audio M1000
- 1.3 MB - Automotive, Car Amplifier, JL Audio, JL Audio M1000
JL Audio M10IB5
- 518.2 KB - Automotive, Auto subwoofer, JL Audio, JL Audio M10IB5
JL Audio C5-525x
- 614 KB - Automotive, Carspeaker, JL Audio, JL Audio C5-525x
JL Audio C2-400x
- 356.1 KB - Automotive, Carspeaker, JL Audio, JL Audio C2-400x
JL Audio C1-650
- 652.5 KB - Automotive, Carspeaker, JL Audio, JL Audio C1-650
JL Audio 13W7AE
- 2.3 MB - Automotive, Auto subwoofer, JL Audio, JL Audio 13W7AE
JL Audio 13TW5v2-2
- 323 KB - Automotive, Auto subwoofer, JL Audio, JL Audio 13TW5v2-2
JL Audio 12TW3-D4
- 2.7 MB - Automotive, Auto subwoofer, JL Audio, JL Audio 12TW3-D4
JL Audio 12W3v3-2
- 192.4 KB - Automotive, Auto subwoofer, JL Audio, JL Audio 12W3v3-2
JL Audio 10TW1-2
- 343.5 KB - Automotive, Auto subwoofer, JL Audio, JL Audio 10TW1-2
JL Audio e6450
- 314.4 KB - Automotive, Car Amplifier, JL Audio, JL Audio e6450
JL Audio 8W3
- 127.5 KB - Automotive, Auto subwoofer, JL Audio, JL Audio 8W3
JL Audio 12W5
- 46.3 KB - Automotive, Auto subwoofer, JL Audio, JL Audio 12W5
JL Audio 8W6
- 56.3 KB - Automotive, Auto subwoofer, JL Audio, JL Audio 8W6
JL Audio 12W6AE
- 123.6 KB - Automotive, Auto subwoofer, JL Audio, JL Audio 12W6AE
JL Audio 8W7
- 2.5 MB - Automotive, Auto subwoofer, JL Audio, JL Audio 8W7
JL Audio 10W7
- 2.5 MB - Automotive, Auto subwoofer, JL Audio, JL Audio 10W7
JL Audio XR650-CSi
- 238.4 KB - Automotive, Carspeaker, JL Audio, JL Audio XR650-CSi